|
Specials
|
|
|
|
30rd Mil-Spec Magazine
Overstock Sale! Standard Mil-Spec spring and green follower. Fits AR-15, M-16 platform weapons. No sales where restricted.
SKU Number:M-30
|
| |
|
|
TAPCO 30rd AR15 Magazine
Overstock Sale! 30rd AR15 Magazine Tapco SKU# MAG0930 BLACK
SKU Number:TAP-0930
|
| |
|
|
M4-LE
The upper is built off of our standard forged A3 receiver with M4 feed ramps. The barrel is our 4140 steel, M4 profile, 5.56mm chamber and bore, 1/9 twist ratio and 1/2x28 threaded barrel and our proprietary WASP surface treatment. The upper is finished with M4 handguard caps, M4 handguards and an A2 flash hider installed with a crush washer. Standard forged mil-spec lower with mil-spec fire control group and take-down pins and mil-spec 6 position ribbed, reinforced stock.
SKU Number:LE-W455-1604
|
| |
|
|
M4-LE Upper
The upper is built off of our standard forged A3 receiver with M4 feed ramps. The barrel is our 4140 steel, M4 profile, 5.56mm chamber and bore, 1/9 twist ratio and 1/2x28 threaded barrel and our proprietary WASP surface treatment.
SKU Number:LU-W455-1604
|
| |
|
|
M4-LEP II
Gas Piston systems operate cleaner then the direct gas impingement operating systems. With the piston system, the propellant gases that are being diverted at the gas block are now vented at the gas block, instead in the operating system of the upper receiver. Since the fouling from the gas system is not being vented in to the action of your firearm, it stays cooler and cleaner. Our system is designed around the short stroke piston operation. The piston pushes the anti tilt one piece carrier, which unlocks the bolt and allows the piston to return home while the bolt carrier continues to cycle independently.
The upper is built off of our standard forged A3 receiver with M4 feed ramps. The chrome plated gas piston is mounted in a solid one piece steel gas block attached to the barrel by pins. The dedicated, piston specific, anti-tilt bolt carrier is one piece, machined with the piston impingement key(not a bolt on). The carrier uses our standard bolt or any after market 5.56 bolt. The barrel is our 4140 steel, M4 profile, 5.56mm chamber and bore, 1/9 twist ratio and 1/2x28 threaded barrel and our proprietary WASP surface treatment. The upper is finished with M4 handguard caps, M4 handguards and an A2 flash hider installed with a crush washer. Our piston rifles utilize our standard forged mil-spec lower with mil-spec fire control group and take-down pins and mil-spec 6 position ribbed, reinforced stock.
The piston gas block has a gas shut off setting for use with a suppressor to allow for maximum noise reduction. You must replace the crush washer with a peel washer if you plan to mount your suppressor on the original flash hider. All rifles have been factory head spaced and test fired. Included with firearm is 1-30rd mag, manual and lifetime warranty. There is no rear sight with this model. There are no upgrade options available with this model.
SKU Number:LE-W455-1604-P
|
| |
|
|
M4-LEP II Upper
Gas Piston systems operate cleaner then the direct gas impingement operating systems. With the piston system, the propellant gases that are being diverted at the gas block are now vented at the gas block, instead in the operating system of the upper receiver. Since the fouling from the gas system is not being vented in to the action of your firearm, it stays cooler and cleaner. Our system is designed around the short stroke piston operation. The piston pushes the anti tilt one piece carrier, which unlocks the bolt and allows the piston to return home while the bolt carrier continues to cycle independently. The upper is built off of our standard forged A3 receiver with M4 feed ramps. The chrome plated gas piston is mounted in a solid one piece steel gas block attached to the barrel by pins. The dedicated, piston specific, anti-tilt bolt carrier is one piece, machined with the piston impingement key(not a bolt on). The carrier uses our standard Mil-Spec bolt. The barrel is our 4140 steel, M4 profile, 5.56mm chamber and bore, 1/9 twist ratio and 1/2x28 threaded barrel and our proprietary WASP surface treatment. The upper is finished with M4 handguard caps, M4 handguards and an A2 flash hider installed with a crush washer. The piston gas block has a gas shut off setting for use with a suppressor to allow for maximum noise reduction. You must replace the crush washer with a peel washer if you plan to mount your suppressor on the original flash hider. Fits on any standard Mil-Spec lower receiver. All uppers have been factory head spaced and test fired. There are no upgrade options available with this model. Nickel Teflon bolt carriers are discontinued and will come with a phosphated carrier.
SKU Number:LU-W455-1604-P
|
| |
Click for larger image
|
|
Microtech Small Arms Research STG-556
Microtech Small Arms Research STG-556 16" Semi-automatic 223 Rem with 10Rd magazine and 1.5X optic. Bullpup design modeled after the Steyr Aug assault rifle.
SKU Number:MSAR-STG556
|
| | |
|
|
PS90 Short Barrel Coversion
CMMG, Inc will convert your PS90 to a NFA registered short barreled rifle. This service includes removal of old barrel & installation of barrel and hider, registration with ATF, engraving, test firing and transfer to your dealer. Price does not include shipping or the barrel and muzzle attachment. Customers original barrel is NOT returned.
SKU Number:RF-CONV
|
| |
Click for larger image
|
|
$20 CMMG, Inc. Gift Certificate
Don't know what exactly to get someone for a present? A gift certificate takes the guesswork out of it.
SKU Number: *
|
| |
Click for larger image
|
|
$50 CMMG, Inc. Gift Certificate
Don't know what exactly to get someone for a present? A gift certificate takes the guesswork out of it.
SKU Number: *
|
|
|
Contact Us
Order Procedures and Policies
Ammunition Warning
Site Map
Copyright 2009 CMMG, Inc.
|